Realme Flash Tool is an official Windows utility provided by Realme for flashing stock firmware on supported Realme smartphones. It is mainly used to restore official software, fix bootloops, or recover devices that fail to boot properly.
This guide explains how to flash Realme firmware using Realme Flash Tool safely, including supported devices, requirements, flashing steps, and common limitations.
Who This Guide Is For
Use this guide only if all conditions below apply:
- ✔ You are using a supported Realme smartphone
- ✔ Your device firmware is provided in
.ofpor.ozipformat - ✔ You are using a Windows PC
- ✔ Your device model is officially supported by Realme Flash Tool
Do NOT use this guide if:
- ❌ Your Realme device is not listed as supported
- ❌ Your firmware format is incompatible
- ❌ Your bootloader is locked, and flashing is restricted
- ❌ You are trying to flash firmware for another Realme model
⚠️ Warnings & Important Limitations
- Flashing firmware will erase all user data
- Flashing the wrong firmware can hard-brick your device
- Realme Flash Tool has strict device and region restrictions
- Not all Realme models support flashing via this tool
- Some Realme firmware requires authorized flashing
FlashGuideHub does not host firmware files. Always verify that the firmware is official and intended for your exact Realme model and region.
Requirements
Before starting, make sure you have the following:
- Windows PC or Laptop
- Reliable USB cable
- Realme Flash Tool (compatible version)
- Realme USB Drivers installed
- Correct Realme firmware file (
.ofpor.ozip) - At least 50% battery charge
Preparation Steps
- Install Realme USB Drivers on your PC
(Restarting the PC afterward is recommended.) - Extract the Realme Flash Tool archive.
- Place the firmware file in an easily accessible folder.
- Power off the Realme device completely.
Step-by-Step: Flashing Firmware with Realme Flash Tool
Step 1: Launch Realme Flash Tool
- Open the extracted Realme Flash Tool folder
- Run
RealmeFlashTool.exeas Administrator
The tool interface should now load.
Step 2: Load Firmware File
- Click Browse or Select Firmware
- Locate and select the
.ofpor supported firmware file - Confirm the firmware is loaded successfully
Step 3: Boot Device into Flashing Mode
- Power off the phone
- Boot the device into Fastboot / Download mode
(Key combinations vary by model) - Connect the device to the PC using USB
- Click “Loading device” to detect the phone.
If drivers are installed correctly, the tool should detect the device.
Step 4: Start Flashing
- Click Start to begin flashing
- Do not disconnect the device during the process
Flashing typically takes 5–10 minutes.
Step 5: Completion & First Boot
Once flashing completes successfully:
- Disconnect the USB cable
- Power on the device
- Wait patiently — first boot may take longer than usual
Common Realme Flash Tool Issues
If flashing fails, common causes include:
- ❌ Unsupported Realme model
- ❌ Incorrect firmware file
- ❌ Locked bootloader restrictions
- ❌ Missing USB drivers
- ❌ Region mismatch
- ❌ Faulty USB cable or USB port
Many Realme devices cannot be flashed freely due to OEM security restrictions.
Post-Flash Checklist
After flashing:
- Complete Android setup
- Verify Realme UI / Android version
- Confirm network signal and IMEI
- Factory reset if boot issues occur
Frequently Asked Questions
Does Realme Flash Tool unlock the bootloader?
No. Bootloader unlocking is a separate and restricted process.
Does Realme Flash Tool work on all Realme phones?
No. Support depends on model, chipset, and region.
Can Realme Flash Tool fix bootloops?
Yes — if the device and firmware are officially supported.
Final Notes
Realme Flash Tool is an OEM-specific flashing solution with strict limitations. Always confirm device compatibility before flashing and never attempt to flash firmware intended for another model.