Before you flash: Flashing firmware will erase all data on your device. Back up contacts, photos, and apps before proceeding. FlashGuideHub is not responsible for any damage caused by following this guide.
About the Xiaomi Redmi Note 3 (hennessy)
The Xiaomi Redmi Note 3 (hennessy) was launched in November 2015, built on the MediaTek Helio X10 MT6795 platform. Known under codename hennessy (models 2015611 and 2015617), the device features a 5.5-inch 1080p display, an all-metal chassis with rear fingerprint sensor, up to 3 GB of LPDDR3 RAM, and an internal 4000 mAh battery.
Flashing official Fastboot firmware recovers devices from software bootloops, unbricks damaged partition structures, and restores clean factory software. Follow the verified package links and bench steps below to flash your device safely.
Which Flash Mode Should You Use?
MediaTek SP Flash Tool (Recommended for Unbricking)
Low-level factory restoration method using MT6795_Android_scatter.txt to flash stock partition images directly through the MediaTek Preloader / BROM interface.
Xiaomi Mi Flash Tool (Fastboot Flashing)
Standard official method for flashing Fastboot TGZ packages via flash_all.bat over the Android bootloader interface.
TWRP Custom Recovery Sideload & Install
Custom recovery environment used for installing signed ZIP update archives, Xiaomi.eu multilingual ROMs, and Magisk root.
What You Need Before Flashing
A 64-bit Windows PC with SP Flash Tool v5.x and MediaTek VCOM USB drivers installed.
Ensure the 4000 mAh battery has at least 50% charge to prevent drops during partition writes.
Use a verified data transfer cable plugged directly into a rear motherboard USB 2.0 port.
Flashing stock firmware via SP Flash Tool completely erases user data and installed applications.
Decompress the .tgz archive twice using 7-Zip until MT6795_Android_scatter.txt is accessible.
How to Flash the Xiaomi Redmi Note 3 (hennessy) β Quick Overview
These 5 steps are tailored to the Xiaomi Redmi Note 3 (hennessy) (Helio X10 MT6795). For screenshots, an interactive checklist, and troubleshooting, open the full SP Flash Tool guide.
-
Install MediaTek VCOM drivers
-
Extract Fastboot TGZ package
-
Load scatter in SP Flash Tool
-
Connect device in BROM mode
-
Wait for green checkmark circle
Scatter File for MediaTek Helio X10 (MT6795_Android_scatter.txt)
Official Fastboot firmware packages for the Xiaomi Redmi Note 3 hennessy contain the partition mapping descriptor MT6795_Android_scatter.txt. This scatter file indexes essential low-level partitions (preloader, lk, boot, recovery, system, userdata, cache, nvram) flashed via SP Flash Tool.
MT6795_Android_scatter.txt
Official Xiaomi Redmi Note 3 hennessy firmware includes the partition map descriptor MT6795_Android_scatter.txt. Load this file into SP Flash Tool under the Scatter-loading field to map system, boot, and recovery partition boundaries.
Flashing Safety Note: Strictly operate in "Download Only" mode within SP Flash Tool. Never select "Format All + Download", which permanently erases the factory NVRAM partition holding device IMEI and MAC addresses.
Xiaomi Redmi Note 3 (hennessy) Firmware Versions
Official stock firmware downloads for the Xiaomi Redmi Note 3 (hennessy). Verify your hardware model variant before downloading.
| Version | Region | Android Version | Size | MD5 | Download |
|---|---|---|---|---|---|
V9.6.1.0.LHNCNFD |
China Stable (CN) | Android 5.0.2 (MIUI 9.6) | 2.77 GB | bd34f81de6e6e8b378e25908e2d069f3 |
β¬οΈ Download |
V9.2.2.0.LHNCNEK |
Europe Multilingual (Xiaomi.eu) | Android 5.0.2 (MIUI 9.2) | 849.2 MB | 49ef93e1428d5d947736254a0846d6f0 |
β¬οΈ Download |
TWRP 3.7.0_9-0 |
Global Custom Recovery | Custom Recovery | 13.66 MB | c443be700d57789be73e929d95d8612c |
β¬οΈ Download |
Want to check full phone specs and partition details? View the device details on AndroidFirmwareFile.com β
Xiaomi Redmi Note 3 (hennessy) β Important Notes
The Redmi Note 3 hennessy features an integrated 4000 mAh battery without an external battery release switch. If the device freezes or fails to establish a USB handshake during flashing, hold Volume Down and Power together for 12 to 15 seconds to force a hardware reset before reconnecting to your PC.
Troubleshooting Redmi Note 3 hennessy Flashing & BROM Errors
BROM ERROR : S_AUTH_HANDLE_IS_NOT_FOUND (5007)
The MediaTek bootloader security layer rejected the Download Agent authentication handshake. Technicians advise loading the customized DA_SWSEC.bin inside SP Flash Tool, or executing an MTK Auth Bypass utility before clicking Download.
PMT changed for the ROM; it must be downloaded (Error 8038)
The partition table layout in the target scatter file differs from the layout currently written to internal eMMC memory. Technicians recommend selecting "Firmware Upgrade" in the SP Flash Tool dropdown (while ensuring nvram remains protected) instead of formatting the board.
BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
SP Flash Tool initialized the MT6795 processor but failed to initialize external LPDDR3 RAM. Cause: Wrong scatter file (such as using kenzo/kate Qualcomm files on hennessy), faulty USB data connection, or depleted battery. Technicians recommend verifying the scatter file is MT6795_Android_scatter.txt and charging the battery.
For solving common SP Flash Tool handshake codes, BROM authentication failures, and driver dropouts: MediaTek & SP Flash Tool Error Directory β
Frequently Asked Questions β Xiaomi Redmi Note 3 (hennessy)
The Redmi Note 3 hennessy was Xiaomi's first handset to introduce locked bootloader security checks into the MediaTek Preloader. If an unverified SP Flash Tool version or generic DA is used, the BROM rejects the handshake with error 5007. Workshop technicians recommend using SP Flash Tool v5.1516 or v5.1628 with the custom DA_SWSEC.bin Download Agent, or using an MTK Auth Bypass utility to disable SLA/DAA authentication before flashing.
Selecting "Format All + Download" wipes the entire physical eMMC storage including protected radio frequency blocks (nvram and nvdata). On hennessy, erasing NVRAM destroys factory baseband calibration, serial numbers, IMEI addresses, and Wi-Fi MAC addresses, leaving the handset unable to register on cellular networks. Technicians must strictly operate in "Download Only" mode.
When a bad flash corrupts the preloader partition, hennessy falls back to native silicon BROM mode, enumerating as "MediaTek USB Port" instead of "Preloader USB VCOM". To recover, open SP Flash Tool, load the official scatter file, click Download, and connect the phone while holding Volume Down. If the PC fails to detect it, disconnect the internal battery ribbon connector for 10 seconds to reset the PMIC before plugging in.
TWRP Error 7 occurs when the updater-script in the ZIP package checks device model asserts and fails to match "hennessy" or "HMNote3". Technicians recommend updating to official TWRP 3.7.0 or opening the ROM archive using 7-Zip, editing META-INF/com/google/android/updater-script with Notepad++, and removing the leading getprop/assert lines before retrying installation.
Ready to Flash?
Follow the full step-by-step SP Flash Tool guide with interactive progress tracking, prerequisite checklist, and complete troubleshooting.