Before you flash: Flashing firmware will erase all data on your device. Back up contacts, photos, and apps before proceeding. FlashGuideHub is not responsible for any damage caused by following this guide.
About the Xiaomi Mi Pad 2
The Xiaomi Mi Pad 2 (codename: latte) launched in November 2015 as Xiaomi's only tablet engineered around the Intel Atom x5-Z8500 (14nm Cherry Trail) platform. The device features a sharp 7.9-inch 2048x1536 display and a 6,190 mAh battery.
Whether you need to recover a tablet stuck on the boot screen, clear away unofficial reseller bloatware, or switch the partition layout back to Android after running Windows 10, this guide provides verified, step-by-step instructions.
Which Flash Mode Should You Use?
Mi Flash Tool (Fastboot ROM)
The official flashing route for latte. Mi Flash Tool runs flash_all.bat to flash boot, system, and userdata partitions in a single clean pass. Requires an unlocked bootloader and erases all internal data.
Fastboot CLI (Command Line)
Flash individual partition images (such as custom recovery) directly from your command prompt using Google Platform Tools.
Intel DNX Mode (Phone Flash Tool)
Low-level Intel firmware download mode used to re-partition internal storage and switch between Windows 10 and Android partition tables.
Pre-Flash Requirements for the Intel Atom Mi Pad 2
Your tablet bootloader must be unlocked using "fastboot oem unlock" before flashing partition images.
A Windows computer with official Intel Android USB drivers installed so Fastboot mode connects without drops.
A reliable USB Type-C data cable plugged directly into a rear PC motherboard port.
Ensure the 6,190 mAh battery has ample charge so the tablet does not cut power during the flashing process.
Flashing with flash_all.bat completely formats internal eMMC storage. Copy essential files to a PC first.
5-Minute Mi Flash & OEM Unlock Steps (latte)
These 5 steps are tailored to the Xiaomi Mi Pad 2 (Intel Atom x5-Z8500). For screenshots, an interactive checklist, and troubleshooting, open the full Mi Flash Tool guide.
-
Confirm your tablet codename is latte in Fastboot mode
-
Unlock the bootloader using standard OEM unlock
-
Extract latte_images_V9.6.2.0.LACCNFD_20180702.0000.00_5.1_cn_6f8e742f80.tgz twice with 7-Zip
-
Configure Mi Flash Tool with clean all
-
Connect via rear USB and flash the partitions
Extracting x5-Z8500 Fastboot TGZ & flash_all.bat
Xiaomi distributes official Mi Pad 2 factory firmware as compressed .tgz Fastboot packages. Once extracted twice using 7-Zip, the root directory contains the master flashing scripts (flash_all.bat for Windows, flash_all.sh for Linux/macOS) alongside individual partition binaries (boot.img, system.img, and recovery.img):
flash_all.bat
Xiaomi factory firmware is distributed as a compressed .tgz Fastboot package (latte_images_V9.6.2.0.LACCNFD_20180702.0000.00_5.1_cn_6f8e742f80.tgz). Once extracted twice using 7-Zip, flash_all.bat (for Windows) and flash_all.sh (for Linux/macOS) sit in the root directory alongside an images subfolder containing individual partition binaries. Point Mi Flash Tool directly to the top-level folder.
The Mi Pad 2 runs an Intel Atom x86 architecture. Never flash packages from other Mi Pad models (such as the Nvidia-based Mi Pad 1, MediaTek-based Mi Pad 3, or Snapdragon-based Mi Pad 4), as ARM binaries will cause a hard brick.
Inside the extracted .tgz folder, flash_all.bat sits at the root level. Point Mi Flash Tool directly to this top-level directory (e.g. C:\latte_fw), not inside the images subfolder.
Important: If the tablet currently runs Windows 10, running flash_all.bat will fail because the internal eMMC storage uses Windows EFI partition tables. You must re-partition using Intel Phone Flash Tool in DNX mode before flashing MIUI.
Xiaomi Mi Pad 2 Firmware Versions
Tested stock Fastboot builds for the China release of the Xiaomi Mi Pad 2. If you need recovery packages, Xiaomi.eu multilingual ROMs, or custom recovery images, browse the complete repository below.
| Version | Region | Android Version | Size | MD5 | Download |
|---|---|---|---|---|---|
V9.6.2.0.LACCNFD |
China (CN) β MIUI 9.6 (Android 5.1) | Android 5.1, Jul 2018 | 1.00 GB | 6f8e742f80357e695135637b77137abc |
β¬οΈ Download |
Browse all Recovery ZIPs, Xiaomi.eu multilingual builds, and Intel x86 TWRP on AndroidFirmwareFile.com β View full archive on AndroidFirmwareFile.com β
Switching from Windows 10 & x86 Partition Notes
The Xiaomi Mi Pad 2 (hardware codename 'latte') is built on Intel's 14nm Atom x5-Z8500 Cherry Trail quad-core platform with an Intel HD Graphics engine, a 7.9-inch 2048x1536 display, and a 6,190 mAh battery. In retail channels, it was sold under model numbers 2015715 (16GB) and 2015716 (64GB).
Because the device was a China-exclusive release, official firmware is available only in the China Stable branch on Android 5.1 Lollipop (MIUI 9.6 build V9.6.2.0.LACCNFD). For European languages and Google Play Services, users can install the community-maintained Xiaomi.eu ROM via the Intel x86_64 TWRP recovery image compiled by tank0412.
Troubleshooting Xiaomi Mi Pad 2 Flashing Issues
FAILED (remote: "command not allowed") or Bootloader Locked Rejection
Fastboot rejects write commands if the tablet bootloader is locked. On the Intel-based Mi Pad 2, enter Fastboot mode (Volume Down + Power) and execute "fastboot oem unlock" in your command prompt. The tablet will prompt for confirmation; accept it to unlock partition writing.
Intel Android Virtual Com Port Not Detected: Tablet missing from Mi Flash device table
Windows 10 and 11 often fail to detect the Intel Cherry Trail composite fastboot device without the official Intel Android USB Driver. Download and install the Intel Android USB Driver package, reconnect the tablet to a rear motherboard USB 2.0 port, and verify that "Android Device" appears in Windows Device Manager without a yellow warning exclamation mark.
Partition Table Mismatch / GPT Signature Error: flash_all.bat fails during partition write
This occurs when attempting to flash Android fastboot images onto a 64GB Mi Pad 2 that was previously converted to Windows 10. The tablet's eMMC storage retains Windows EFI/NTFS partitions that Android fastboot cannot write over. Re-partition the internal storage back to Android format using Intel Phone Flash Tool in DNX mode before running flash_all.bat.
Mi Flash Error: "cannot open latte_images...tgz" or flash_all.bat not found
Mi Flash Tool cannot read directly from compressed .tgz or .tar archive files. You must extract the .tgz archive twice using 7-Zip until the actual folder containing flash_all.bat and the images subfolder is exposed. In Mi Flash Tool, select this extracted folder directly.
For the full firmware error database: Fastboot Error Directory β
Mi Pad 2 Flashing, TWRP & Driver Q&A
Windows 10 configures the tablet's eMMC storage with UEFI GPT partition tables formatted in NTFS, which prevents Android fastboot scripts from recognizing the partition layout. To switch back, put the tablet into DNX Fastboot mode (holding Volume Up + Power until DNX appears) and use the Intel Phone Flash Tool with the official Android partition configuration file (gpt.bin) to recreate the native Android partition structure before running flash_all.bat.
The unofficial TWRP 3.1.1.0 build by tank0412 relies on Intel Cherry Trail Direct Rendering Manager (DRM) kernel graphics drivers, which run in software rendering mode inside recovery. This introduces a slight visual polling delay when touching on-screen buttons. The touch coordinates remain completely accurate, and backup or ZIP flashing operations run at full hardware speed.
No. Unlike Qualcomm or MediaTek phones that store unique IMEI, radio calibration, and Wi-Fi MAC tables inside sensitive persist or nvram partitions, the Mi Pad 2 is a Wi-Fi-only tablet without a cellular baseband. Running flash_all.bat will safely overwrite all standard factory partitions without risk of losing cellular network calibration.
Because the China Stable Fastboot image (latte_images_V9.6.2.0.LACCNFD_20180702.0000.00_5.1_cn_6f8e742f80.tgz) does not include Google Mobile Services, you can either install the Google Installer v2 APK directly inside MIUI to download Play Services, or download the community Xiaomi.eu ROM and x86 TWRP image from our AndroidFirmwareFile archive.
Ready to Flash?
Follow the full step-by-step Mi Flash Tool guide with interactive progress tracking, prerequisite checklist, and complete troubleshooting.