Before you flash: Flashing firmware will erase all data on your device. Back up contacts, photos, and apps before proceeding. FlashGuideHub is not responsible for any damage caused by following this guide.
About the Xiaomi Redmi 4 (Standard Edition)
The Xiaomi Redmi 4 (Standard Edition) (codename: prada) debuted in November 2016 on Qualcomm's Qualcomm Snapdragon 430 MSM8937 (28nm) platform with a 720p 5.0-inch display and a 4,100 mAh battery.
Whether you are rescuing a bricked phone in Qualcomm EDL 9008 mode with prada_global_images_V10.2.2.0.MCEMIXM_20190508.0000.00_6.0_global_299e7070e4.tgz or setting up custom ext4/f2fs recovery via recovery-3.1.1-0_V3.zip, follow the verified steps below.
Which Flash Mode Should You Use?
Mi Flash Tool β EDL 9008 Mode (Locked or Bricked)
Writes stock eMMC partitions over Qualcomm QDLoader 9008 without needing an unlocked bootloader.
Mi Flash Tool / Fastboot CLI (Unlocked Devices)
Executes flash_all.bat or installs extracted recovery images directly over the Android Bootloader interface.
TWRP / Local Updater (Recovery ZIP)
Installs signed stock OTA ZIP updates on running Global systems or flashes Xiaomi.eu and recovery-3.1.1-0_V3.zip inside custom recovery.
Essential Prep Before Flashing Redmi 4 (prada)
Use Xiaomi's 64-bit Mi Flash tool on 64-bit Windows so Qualcomm 9008 Firehose transfers do not hit 32-bit RAM errors.
Older MicroUSB sockets loosen over time. Connect a snug, shielded data cable directly to a rear motherboard USB 2.0 port.
Unpack the .tgz archive twice using 7-Zip directly into C:\prada_fw\ without spaces so flash_all.bat runs cleanly.
Ensure at least 40% battery charge (or verify battery flex seating if opening the cover for EDL test points) before flashing.
Running flash_all.bat wipes internal 16 GB eMMC storage clean. Save personal data off the phone before starting.
Mi Flash & Qualcomm 9008 Steps for Snapdragon 430
A quick 5-step overview built specifically for the Xiaomi Redmi 4 (Standard Edition). The full Mi Flash Tool guide adds screenshots, progress tracking, and fixes for common errors.
-
Install 64-bit Mi Flash Tool and Qualcomm HS-USB QDLoader 9008 drivers
-
Extract prada_global_images_V10.2.2.0.MCEMIXM_20190508.0000.00_6.0_global_299e7070e4.tgz twice to C:\prada_fw\
-
Boot to EDL 9008 (adb reboot edl / test points) if locked, or Fastboot (Vol Down + Power) if unlocked
-
Select C:\prada_fw\ in Mi Flash Tool, click Refresh, and confirm "clean all"
-
Click Flash immediately after entering EDL so eMMC writes finish cleanly
Finding flash_all.bat & 8937 Firehose Files in Snapdragon 430 Packages
Official Xiaomi Redmi 4 (prada) Fastboot archives are double-packed .tgz files. Extracting twice with 7-Zip places flash_all.bat at the outer directory next to the images folder holding rawprogram0.xml, patch0.xml, and the MSM8937 Firehose loader:
flash_all.bat
Extracting prada_global_images_V10.2.2.0.MCEMIXM_20190508.0000.00_6.0_global_299e7070e4.tgz twice with 7-Zip reveals flash_all.bat at the outer directory next to the images folder holding rawprogram0.xml and the MSM8937 Firehose loader. Select the outer directory inside Mi Flash Tool.
Codename prada covers ONLY the 5.0-inch 720p Snapdragon 430 Redmi 4 Standard (models 2016090 and 2016091). Never use files built for Redmi 4 Prime (markw), Redmi 4X / India's Redmi 4 (santoni), or Redmi 4A (rolex).
Point Mi Flash Tool at the top folder containing flash_all.bat (for example C:\prada_fw\), not the inner images folder.
Keep "clean all" checked at the bottom right; choosing "clean all and lock" on cross-regional software can freeze boot.
Xiaomi Redmi 4 (Standard Edition) Firmware Versions
Tested Fastboot, Recovery, and TWRP 3.1.1-0 V3 builds for the Xiaomi Redmi 4 (Standard Edition) (prada). Visit the full archive below for Xiaomi.eu V10.2.1.0.MCECNXM and China Recovery ZIP downloads.
| Version | Region | Android Version | Size | MD5 | Download |
|---|---|---|---|---|---|
V10.2.2.0.MCEMIXM |
Global (MI / HM4Global) β MIUI 10.2 | Android 6.0 (Marshmallow), May 2019 | 1.57 GB | 299e7070e42f65c03e7b188d2a0cbd11 |
β¬οΈ Download |
V10.2.2.0.MCEMIXM (OTA) |
Global Recovery ZIP | Android 6.0 (Marshmallow), May 2019 | 1.37 GB | 0a6d0684b592fe94fd9b74ab4224d897 |
β¬οΈ Download |
V10.2.2.0.MCECNXM |
China (CN / HM4) β MIUI 10.2 | Android 6.0 (Marshmallow), May 2019 | 1.69 GB | 0f8b1cf46afceed7cfe318512204b7ba |
β¬οΈ Download |
TWRP 3.1.1-0 V3 (Kizoky) |
Community Recovery (prada) | Custom Recovery ZIP | 20.7 MB | 809b513fe1c21f4cb8695bb418f06501 |
β¬οΈ Download |
Browse all 6 MIUI 10, Xiaomi.eu & Kizoky TWRP builds for Redmi 4 (prada) on AndroidFirmwareFile.com β View full archive on AndroidFirmwareFile.com β
Choosing EDL 9008, Fastboot & Kizoky TWRP 3.1.1-0 V3
The Xiaomi Redmi 4 Standard Edition (codename prada, models 2016090 / 2016091) runs Qualcomm's Snapdragon 430 (MSM8937). Using prada_global_images_V10.2.2.0.MCEMIXM_20190508.0000.00_6.0_global_299e7070e4.tgz, locked handsets recover reliably via Qualcomm EDL 9008 while unlocked units flash over Fastboot.
For running Global builds, miui_HM4Global_V10.2.2.0.MCEMIXM_0a6d0684b5_6.0.zip installs cleanly via the Updater app, while unlocked devices can run Kizoky's recovery-3.1.1-0_V3.zip for ext4/f2fs storage access and custom ROM flashing.
Fixing Redmi 4 (prada) Locked Fastboot, Sahara & Driver Errors
Status: "FAILED (remote: Partition flashing is not allowed)"
This happens when Fastboot commands target a Redmi 4 whose bootloader is still locked. Switch into Qualcomm EDL 9008 mode ("adb reboot edl", a deep-flash MicroUSB cable, or shorting the rear motherboard test points) and run Mi Flash over the COM port.
Log Error: "Cannot receive hello packet" (Sahara Timeout)
MSM8937 exits its active Sahara listening window if the handset waits in EDL 9008 too long before Mi Flash starts communicating with prog_emmc_firehose_8937*.mbn. Hold Power 10 seconds to reset, re-enter 9008 fresh, hit Refresh, and press Flash right away.
Tool Dialog: "Missmatching image and device" or Path Too Deep
Triggered either by accidentally downloading Redmi 4 Prime (markw) / Redmi 4X (santoni) images or leaving spaces inside folder paths. Confirm your archive prefix is prada and unpack twice with 7-Zip to C:\prada_fw\.
Device Manager Alert: "QHSUSB_BULK" Yellow Exclamation
Windows spotted the Snapdragon 430 USB emergency device without signed Qualcomm 9008 drivers. Run Mi Flash Tool -> Driver -> Install on 64-bit Windows (or temporarily disable Driver Signature Enforcement) until it appears cleanly as QDLoader 9008.
Need troubleshooting for another Qualcomm COM or Fastboot status message? Mi Flash & Qualcomm EDL Error Directory β
EDL Access, TWRP ZIP Unpacking & f2fs Storage Q&A
Yes. The 2016 Snapdragon 430 platform used inside the Redmi 4 (prada) relies on an unauthenticated Firehose loader (prog_emmc_firehose_8937*.mbn) bundled inside every Fastboot .tgz download. Even on a locked bootloader, entering Qualcomm QDLoader 9008 lets you restore V10.2.2.0.MCEMIXM cleanly without a Xiaomi service account.
Because Kizoky packaged TWRP 3.1.1-0 V3 as a flashable archive (recovery-3.1.1-0_V3.zip), you have two options on an unlocked Redmi 4: if you already have a working custom recovery, flash the ZIP directly; if starting from stock Mi Recovery, unzip recovery-3.1.1-0_V3.zip on your PC to extract the recovery image inside and install it with "fastboot flash recovery".
Some Redmi 4 units carry encrypted or custom f2fs /data layouts that trigger mount failures in older generic recoveries. Inside TWRP 3.1.1-0 V3, go to Wipe -> Format Data (type yes) to rebuild clean ext4 encryption metadata before sideloading or installing xiaomi.eu_multi_HM4_V10.2.1.0.MCECNXM_v10-6.0.zip.
Yes. Official MIUI flash_all.bat and Firehose rawprogram0.xml tables preserve modemst1, modemst2, and fsg so dual-SIM IMEI numbers, Wi-Fi/Bluetooth MAC addresses, and RF calibration remain untouched during stock restoration.
Ready to Flash?
Follow the full step-by-step Mi Flash Tool guide with interactive progress tracking, prerequisite checklist, and complete troubleshooting.