Before you flash: Flashing firmware will erase all data on your device. Back up contacts, photos, and apps before proceeding. FlashGuideHub is not responsible for any damage caused by following this guide.
About the Xiaomi Redmi Note 13 Pro 4G / POCO M6 Pro
The Xiaomi Redmi Note 13 Pro 4G / POCO M6 Pro (codename: emerald) launched in January 2024 on MediaTek's MediaTek Helio G99-Ultra (6nm TSMC) platform with UFS 2.2 storage, an under-display optical fingerprint scanner, and Virtual A/B dynamic partitions.
Whether you are restoring European HyperOS 3.0 via emerald_eea_global_images_OS3.0.303.0.WNFEUXM_20260923.0000.00_16.0_eea_de1befbfa2.tgz or recovering from an update loop, follow the hardware checks and flashing steps below carefully.
Which Flash Mode Should You Use?
Mi Flash Tool (Fastboot + fastbootd Restore)
Writes full factory HyperOS 3.0 images (preloader, boot, dtbo, vbmeta, and super.img) cleanly on unlocked emerald devices.
Mi Assistant (Stock Recovery Sideload)
Installs signed Recovery OTA ZIP packages on locked bootloaders when the phone can still enter stock Mi Recovery.
MediaTek BROM / Preloader (SP Flash Tool)
Low-level unbrick mode for dead or hard-bricked units that cannot enter Fastboot or Recovery.
Before You Start: Helio G99-Ultra & NTFS Drive Checks
Mi Flash Tool Fastboot mode requires an unlocked bootloader; locked units must use Mi Assistant Recovery sideload or authorized BROM recovery.
The 7 GB+ .tgz Fastboot archive extracts beyond 12 GB and exceeds FAT32's 4 GB single-file limit.
Direct motherboard USB 2.0 prevents connection dropouts when emerald transitions from Fastboot into userspace fastbootd.
Maintain solid charge before flashing UFS 2.2 partitions so a power drop cannot corrupt the preloader header.
Never wipe persist—it holds optical under-display fingerprint and 200 MP / 64 MP camera calibration data.
Mi Flash & fastbootd Walkthrough for Redmi Note 13 Pro 4G & POCO M6 Pro
5-step quick reference for the Xiaomi Redmi Note 13 Pro 4G / POCO M6 Pro. Need visuals or troubleshooting help? The full Mi Flash Tool guide covers everything in detail.
-
Verify Unlocked Bootloader Status and Install Platform-Tools v35+ Before Flashing
-
Extract emerald_eea_global_images_OS3.0.303.0.WNFEUXM_20260923.0000.00_16.0_eea_de1befbfa2.tgz Twice to C:\emerald_fw\
-
Boot Into Fastboot Mode (Volume Down + Power) and Connect to a Rear USB 2.0 Port
-
Select "clean all" (flash_all.bat) in Mi Flash Tool and Keep Persist Untouched
-
Allow Automatic fastbootd Transition and Wait 5–8 Minutes for First HyperOS 3.0 Boot
Inside the MT6789 Fastboot Archive (flash_all.bat)
Official Xiaomi emerald Fastboot archives use flash_all.bat (and fastbootd dynamic partition scripts) for unlocked phones, while emergency MediaTek scatter flashing in SP Flash Tool requires SLA/DA authentication:
flash_all.bat
Extract emerald_eea_global_images_OS3.0.303.0.WNFEUXM_20260923.0000.00_16.0_eea_de1befbfa2.tgz twice with 7-Zip onto a short folder path like C:\emerald_fw\ to reveal flash_all.bat beside the images directory.
Codename emerald covers both the Redmi Note 13 Pro 4G (23117RA68G) and POCO M6 Pro 4G (2312FPCA6G).
Always choose "clean all" (flash_all.bat) when switching between Global, EEA, Indonesia, Russia, and Turkey builds.
Never wipe persist during cross-region flashes—optical fingerprint and 200 MP / 64 MP camera calibration depend on it.
Xiaomi Redmi Note 13 Pro 4G / POCO M6 Pro Firmware Versions
Recommended EEA Fastboot package for the unified Xiaomi Redmi Note 13 Pro 4G / POCO M6 Pro (emerald) hardware platform. Need Global, Russia, Indonesia, Turkey, or Recovery OTA ZIP builds? Browse the complete archive below.
| Version | Region | Android Version | Size | MD5 | Download |
|---|---|---|---|---|---|
OS3.0.303.0.WNFEUXM (EEA / UK Fastboot) |
Europe / EEA (EU) | Android 16.0 (HyperOS 3.0) | 7.06 GB | de1befbfa2388850f3bc92b5746aa645 |
⬇️ Download |
Looking for Global OS3.0.307.0, Russia, Indonesia, Turkey, or Recovery OTA ZIPs? Browse all 9 emerald firmware packages on AndroidFirmwareFile.com →
emerald Twin Notes, Persist Protection & Region Locks
Choosing Between Fastboot & Recovery on emerald: If your bootloader is unlocked, extract emerald_eea_global_images_OS3.0.303.0.WNFEUXM_20260923.0000.00_16.0_eea_de1befbfa2.tgz twice onto an NTFS drive and flash with Mi Flash Tool using clean all. If your bootloader is still locked, grab the matching Recovery OTA ZIP from AndroidFirmwareFile and sideload it through Stock Recovery (“Connect with MIAssistant”).
Troubleshooting emerald MediaTek BROM, fastbootd & Relock Issues
MediaTek BROM / SLA Rejection: "STATUS_BROM_CMD_SEND_DA_FAIL" or "0xC0060003" in SP Flash Tool
On the Helio G99-Ultra (MT6789) board, MediaTek BootROM enforces Secure Level Authentication (SLA) and signed Download Agent (DA) checks. Standard SP Flash Tool or unauthenticated mtkclient connections fail when trying to flash scatter files without an authorized Xiaomi auth file (auth_sv5.auth) or compatible SLA/DA bypass.
Fastbootd Super Partition Stall: "FAILED (remote: 'data too large')" or USB Drop Mid-Write
HyperOS 3.0 Android 16 packages on emerald carry a multi-gigabyte dynamic super.img that switches the phone from bootloader Fastboot into userspace fastbootd mid-script. Outdated Platform-Tools or unpowered USB 3.x front-panel hubs often drop the connection during that handoff. Community repair notes recommend Platform-Tools v35+ and a rear motherboard USB 2.0 port.
Cross-Region Lock Freeze: "This MIUI/HyperOS version can't be installed on this device"
Selecting "clean all and lock" (flash_all_lock.bat) when moving between Global (WNFMIXM), EEA (WNFEUXM), Indonesia (WNFIDXM), Russia (WNFRUXM), or Turkey (WNFTRXM) triggers a regional certificate mismatch once the bootloader relocks. Always keep "clean all" selected unless flashing the exact factory region SKU.
Need help with additional Fastboot or MediaTek driver codes? Mi Flash & MediaTek Error Directory →
Magisk boot.img, Slot Switching & Unlock Quota Q&A
Unlike newer Qualcomm GKI boards that move the ramdisk to init_boot.img, the MediaTek Helio G99-Ultra emerald platform uses the classic boot.img for Magisk patching. Extract boot.img from the Fastboot archive matching your exact installed HyperOS 3.0 build, patch it inside Magisk, and flash via fastboot flash boot magisk_patched.img.
The persist partition stores factory calibration data for the under-display optical fingerprint sensor, gyroscope, and camera sensor parameters (200 MP on 23117RA68G vs 64 MP on 2312FPCA6G). Standard flash_all.bat scripts leave persist alone—never erase or overwrite it with a mismatched dump, or optical fingerprint unlock and camera modes can stop working.
Xiaomi limits daily HyperOS bootloader unlock slots globally, frequently returning "Application quota reached" or HTTP 403 errors. If your bootloader is still locked and the phone cannot boot, you cannot use Mi Flash Fastboot mode; instead, boot into Stock Recovery (Volume Up + Power) and sideload the matching signed Recovery OTA ZIP via Mi Assistant, or use an authorized MediaTek service tool.
Because emerald uses Virtual A/B partitions, a failed update can leave the inactive slot unbootable. In Fastboot mode, run fastboot getvar current-slot to check whether slot a or b is active, then run fastboot --set-active=a (or b) to fall back to the previous working system slot without wiping userdata.
Ready to Flash?
Follow the full step-by-step Mi Flash Tool guide with interactive progress tracking, prerequisite checklist, and complete troubleshooting.