Before you flash: Flashing firmware will erase all data on your device. Back up contacts, photos, and apps before proceeding. FlashGuideHub is not responsible for any damage caused by following this guide.
About the OPPO Mirror 5
The OPPO Mirror 5 was released in July 2015, built upon the Qualcomm Snapdragon 410 (MSM8916) processor with an Adreno 306 GPU and 2GB of RAM. Flashing official stock firmware restores corrupted partitions, unbricks frozen devices, and returns ColorOS to factory configuration.
Official firmware packages for this smartphone utilize Qualcomm Emergency Download (EDL 9008) mode, flashed primarily via QFIL or QPST. The walkthrough below details prerequisite setup, XML partition selection, and troubleshooting steps.
Which Flash Mode Should You Use?
QFIL (Qualcomm Flash Image Loader)
Standard EDL 9008 flashing method for extracted rawprogram0.xml and patch0.xml packages. Communicates directly with the Snapdragon 410 boot ROM and works without bootloader unlocking.
MSM Download Tool
Oppo factory flash utility for official OFP or unpacked firmware packages. Connects over the same Qualcomm 9008 interface to verify project checksums and write factory partitions.
SP Flash Tool (Not Applicable)
SP Flash Tool is designed exclusively for MediaTek chipsets and is incompatible with the Qualcomm Snapdragon 410 processor in the Oppo Mirror 5. Do not attempt to use scatter-based tools on this device.
Requirements for Flashing the OPPO Mirror 5
A computer running 64-bit Windows 7, 8, 10, or 11 is required to run QPST/QFIL and load the Qualcomm QDLoader driver stack.
Download an official firmware package matching your exact sub-model (A51w, A51f, or A51) and unpack it completely before opening QFIL.
Use a reliable microUSB data cable connected directly to a rear motherboard USB 2.0 port. Avoid USB hubs or front-panel extensions.
Writing raw system partitions over EDL mode draws constant power. Ensure the internal 2420mAh battery has sufficient charge before starting.
EDL flashing performs a clean overwrite of user partitions, wiping all internal storage data, photos, and apps.
5-Minute QFIL & EDL Restoration Steps
A quick 5-step overview built specifically for the OPPO Mirror 5. The full QFIL guide adds screenshots, progress tracking, and fixes for common errors.
-
Extract Oppo_Mirror_5_A51W_EX_11_A.16_160815.zip and verify rawprogram0.xml
-
Install Qualcomm QDLoader 9008 drivers and restart your computer
-
Open QFIL, choose Flat Build, and load prog_emmc_firehose_8916.mbn
-
Hold Volume Up and Volume Down to enter Qualcomm 9008 EDL mode
-
Click Download to write partitions and reboot into ColorOS after finish
Qualcomm MSM8916 Firehose Package Layout
The OPPO Mirror 5 uses the Qualcomm Firehose programmer prog_emmc_firehose_8916.mbn with rawprogram0.xml and patch0.xml to write partition images to eMMC flash memory.
prog_emmc_firehose_8916.mbn / rawprogram0.xml
When extracted, the Oppo Mirror 5 firmware package contains the Firehose programmer prog_emmc_firehose_8916.mbn along with rawprogram0.xml and patch0.xml. These XML files define the exact partition offsets on the 16GB eMMC storage (boot, system, recovery, modem, and userdata). QFIL parses rawprogram0.xml to write partition binaries to the phone. Because this device uses a Qualcomm Snapdragon 410 chipset, it does not use a MediaTek scatter file.
Confirm you are flashing the package matching your specific hardware model (A51w for qHD screen, A51f or A51 for HD screen) before starting QFIL.
Official Stock Firmware Packages for OPPO Mirror 5
Official stock firmware packages for the OPPO Mirror 5. Verify your hardware model (A51w, A51f, or A51) before proceeding with an EDL flash.
| Version | Region | Android Version | Size | MD5 | Download |
|---|---|---|---|---|---|
EX_11_A.16_160815 |
A51w β Global / International (EX) | Android 5.1 | 1.30 GB | β | β¬οΈ Download |
EX_11_A.10_160304 |
A51f β International / South Asia (EX) | Android 5.1 | 1.46 GB | 1a673ebbdea6f062c268ada4696c662a |
β¬οΈ Download |
051215 |
A51 β China Domestic | Android 5.1 | 1.08 GB | β | β¬οΈ Download |
AndroidFirmwareFile maintains the full historical archive including mirrors and regional variants. View full OPPO Mirror 5 archive on AndroidFirmwareFile.com β
MSM8916 Partition Details & Display Hardware
The international firmware package Oppo_Mirror_5_A51W_EX_11_A.16_160815.zip provides the complete factory partition table for the A51w. If your device fails to boot after an OTA update or shows a blank screen, flashing in Qualcomm EDL 9008 mode restores all critical partitions including the Little Kernel bootloader (aboot), modem radio baseband, and ColorOS system image.
Troubleshooting OPPO Mirror 5 Flashing & EDL Connection Issues
Sahara Fail: QSaharaServer Fail: Process fail
The MSM8916 boot ROM failed to establish the initial USB handshake with QFIL. This commonly happens when connecting via USB 3.0 ports or front-panel hubs. Connect directly to a rear motherboard USB 2.0 port, reseat the microUSB cable, and enter EDL mode fresh before clicking Download.
Unable to send FireHose nop / Target did not respond
The prog_emmc_firehose_8916.mbn programmer initialized in phone RAM, but communication with the eMMC flash chip timed out. This occurs when the non-removable battery voltage drops below 3.2V. Disconnect the device, charge it on a standard 5V wall charger for 30 minutes, and retry.
LCD panel driver panic (dtb mismatch between qHD and HD boards)
Occurs when an A51w qHD package is flashed onto an A51f or China A51 HD board revision. The kernel device tree cannot communicate with the display panel controller. Re-flash the exact package matching your model designation (A51w for qHD, A51f for HD).
For additional Qualcomm flashing error codes, driver fixes, and emergency unbrick guides: QFIL & Qualcomm EDL Troubleshooting Guide β
Workshop Troubleshooting & Recovery Q&A
Make sure the phone is powered completely off. If it is looping, hold the Power key for 10 seconds until the screen stays dark. Press and firmly hold both Volume Up and Volume Down together, then insert the microUSB cable into the phone. Continue holding both volume buttons until your PC plays the USB connection chime. If the phone turns on to the Oppo logo or battery charging symbol, disconnect the cable, wait 5 seconds, and retry the button combination.
A "Sahara Fail" error occurs when the initial communication between QFIL and the Qualcomm MSM8916 boot ROM drops out. This is most frequently caused by plugging into a USB 3.0/3.1 port or an unpowered front-panel USB hub, which introduces latency incompatible with older Qualcomm boot ROMs. Switch your USB cable to an onboard USB 2.0 port on the back of your computer motherboard and reconnect the device into EDL mode.
No, provided you flash the standard factory package. The official rawprogram0.xml file writes system, boot, recovery, and modem partitions, but it leaves the modemst1 and modemst2 partitions untouched. These non-volatile memory partitions house your phone unique RF calibration and IMEI parameters, so your cellular identity is preserved across the flash.
The initial startup after an EDL flash requires 5 to 8 minutes as ColorOS 2.1 builds internal Dalvik/ART caches. If the phone remains on the logo for longer than 10 minutes, unplug the cable, hold Power and Volume Down until it vibrates into ColorOS Recovery, choose English, tap "Wipe data and cache", confirm, and then tap "Reboot".
Ready to Flash?
Follow the full step-by-step QFIL guide with interactive progress tracking, prerequisite checklist, and complete troubleshooting.