Before you flash: Flashing firmware will erase all data on your device. Back up contacts, photos, and apps before proceeding. FlashGuideHub is not responsible for any damage caused by following this guide.
About the Xiaomi Redmi K30 4G / POCO X2
The Xiaomi Redmi K30 4G / POCO X2 (hardware codename phoenix for Redmi K30 4G and phoenixin for POCO X2) was released in December 2019 / February 2020, built on the Qualcomm Snapdragon 730G (SM7150-AB, 8nm) platform with an Adreno 618 GPU, 6.67-inch Full HD+ 120Hz IPS display, quad rear cameras featuring a 64 MP Sony IMX686 sensor, and a 4500 mAh battery with 27W wired fast charging.
This guide provides step-by-step instructions for flashing official stock Fastboot firmware on the Xiaomi Redmi K30 4G / POCO X2 using Xiaomi Mi Flash Tool. Whether you need to recover a phone stuck on the boot screen, fix software errors after an update, or return to a clean factory state, follow these verified steps to flash safely.
Which Flash Mode Should You Use?
Xiaomi Mi Flash Tool (Fastboot)
Official flashing utility for unlocked Xiaomi devices. Writes partition images directly over Fastboot.
TWRP / OrangeFox Custom Recovery
Custom recovery environment for installing recovery ZIPs, custom ROMs, and performing full system backups.
Stock Recovery / Local Update
Official on-device recovery update method for installing official Recovery OTA ZIP packages without wiping personal data.
Essential Equipment & Pre-Flash Driver Preparation
A 64-bit Windows 10/11 computer with official Qualcomm Android USB drivers and Android SDK Platform Tools.
An officially unlocked bootloader via the Xiaomi Mi Unlock utility is mandatory for Fastboot partition flashing.
Ensure the 4500 mAh battery holds at least 50% charge to prevent power loss while writing large system partition images.
Use an authentic data sync cable connected directly to a rear motherboard USB 2.0 port to prevent communication drops.
5-Step Mi Flash & Fastboot Restoration Walkthrough
A condensed step-by-step summary specific to the Xiaomi Redmi K30 4G / POCO X2. Follow the full Mi Flash Tool guide for screenshots, an interactive progress checklist, and complete troubleshooting.
-
Download and extract phoenixin_in_global_images_V12.5.6.0.RGHINXM_20211123.0000.00_11.0_in_794e6c1d4f.tgz with 7-Zip
-
Reboot handset to Fastboot mode via physical key combination
-
Connect to PC USB 2.0 port and verify handshake via fastboot devices
-
Configure Mi Flash with clean all script and verify device ID
-
Flash device and complete initial first-boot MIUI cache rebuild
Fastboot Script Structure & Flashing Modes
Fastboot firmware packages for the Xiaomi Redmi K30 4G and POCO X2 unpack into an images folder containing raw partition binaries alongside automated batch scripts: flash_all.bat (clean flash), flash_all_except_storage.bat (preserve user data), and flash_all_lock.bat (clean flash and relock bootloader). Experienced owners recommend strictly selecting flash_all.bat to format user storage cleanly across UFS 2.1 partitions.
flash_all.bat
Official Fastboot packages for the Xiaomi Redmi K30 4G and POCO X2 contain automated batch scripts for different repair scenarios. Understanding these scripts ensures you select the correct flashing operation in Mi Flash Tool.
Never run flash_all_lock.bat when flashing cross-regional or Xiaomi.eu software on imported hardware, as relocking the bootloader against modified cryptographic signatures causes an immediate hard brick.
Xiaomi Redmi K30 4G / POCO X2 Firmware Versions
Below are verified Fastboot packages for the Xiaomi Redmi K30 4G and POCO X2, including the Indian public stable release and the official Chinese MIUI 13 build. For custom recoveries like TWRP and OrangeFox, browse the master archive.
| Version | Region | Android Version | Size | MD5 | Download |
|---|---|---|---|---|---|
V12.5.6.0.RGHINXM (MIUI 12.5 Official) |
India (IN) β POCO X2 | Android 11.0 | 3.4 GB | 794e6c1d4f748c61c74ac9ec7945e53e |
β¬οΈ Download |
V13.0.6.0.SGHCNXM (MIUI 13 Official) |
China (CN) β Redmi K30 4G | Android 12.0 | 4.9 GB | edf8a2c9f63046c2a32c0028b57f0f61 |
β¬οΈ Download |
V13.0.6.0.SGHCNXM (MIUI 13 Xiaomi.eu) |
Europe / Multilingual (EU) | Android 12.0 | 3.2 GB | β | β¬οΈ Download |
Need additional packages like official TWRP, OrangeFox recovery, or recovery OTA ZIPs? Browse the full Xiaomi Redmi K30 & POCO X2 archive on AndroidFirmwareFile.com β
Snapdragon 730G Partition Layout & Script Execution Notes
The Qualcomm Snapdragon 730G platform employs dynamic partition management inside the super block on newer MIUI releases. Flashing official packages like phoenix_images_V13.0.6.0.SGHCNXM_20220928.0000.00_12.0_cn_edf8a2c9f6.tgz is performed directly over Fastboot mode via automated batch scripts. Maintain an uninterrupted USB connection throughout the entire process.
Troubleshooting Xiaomi Redmi K30 & POCO X2 Flashing Errors
Fastboot detection timeout: "target didn't report max-download-size over USB 3.0"
The Snapdragon 730G bootloader interface can drop communication on Windows 10/11 when connected to USB 3.0/3.1 ports. Connect the device directly to a rear motherboard USB 2.0 port, install official Qualcomm Android USB drivers, and verify connectivity using "fastboot devices".
Dynamic partition error: "FAILED (remote: Partition table doesn't exist)"
Occurs when attempting to flash core system partition binaries directly via standard fastboot rather than using Mi Flash batch scripts. The Snapdragon 730G utilizes dynamic partitions inside the super block; flashing individual system or vendor images requires switching to fastbootd mode via "fastboot reboot fastboot" or executing flash_all.bat.
Updater-script assert rejection: "assert failed: getprop(\"ro.product.device\") == \"phoenix\""
Triggered when flashing a recovery package or custom ROM built strictly for Redmi K30 (phoenix) onto a POCO X2 (phoenixin). Either flash a unified package supporting both variants or open the updater-script inside the zip archive and add phoenixin to the assert verification line.
Recovery storage mount failure: "Unable to mount /data (0 MB Storage)"
Happens in TWRP or OrangeFox after upgrading Android versions due to File-Based Encryption (FBE) format changes. In the recovery menu, navigate to Wipe > Format Data, type "yes", and confirm to regenerate the internal storage filesystem with matching encryption parameters.
Encountering issues during flashing? Review these verified workshop troubleshooting notes for the Xiaomi Redmi K30 4G and POCO X2. Troubleshooting & Common Errors β
Technical Workshop Questions & Unbricking Mechanics
Flashing Fastboot images or custom recoveries requires unlocking the bootloader via Xiaomi's official Mi Unlock tool. You must bind your Xiaomi account under Developer Options > Mi Unlock Status over mobile cellular data (not Wi-Fi). Xiaomi's authorization servers enforce a mandatory 168-hour (7-day) waiting countdown before the bootloader can be unlocked. Attempting to bypass this countdown with unauthorized third-party tools will not succeed and risks locking your account.
The Redmi K30 4G and POCO X2 utilize a legacy A-only partition layout featuring a dedicated physical recovery partition alongside dynamic partitions in the super block. Because recovery is stored on its own dedicated partition rather than packed into the boot image ramdisk, users can flash custom recoveries directly with the standard command "fastboot flash recovery recovery.img" and boot immediately via "fastboot reboot recovery" without requiring temporary boot patching.
If the bootloader is locked or partition tables are severely corrupted, the device cannot enter Fastboot mode. Emergency recovery requires Qualcomm Emergency Download mode (HS-USB QDLoader 9008). After removing the rear glass cover and unclipping the protective motherboard bracket, two small gold test pads are situated directly adjacent to the battery flex connector. Shorting these pads with fine tweezers while plugging in the USB cable forces the phone into EDL mode.
Selecting "clean all" runs flash_all.bat, which writes fresh system, vendor, boot, and product binaries while preserving the persist partition. The persist block contains unique hardware calibration baselines for the Sony IMX686 64MP sensor, dual-camera focus alignment, and side-mounted fingerprint scanner. Leaving persist untouched prevents post-flash camera errors and keeps biometric unlocking operational.
Ready to Flash?
Follow the full step-by-step Mi Flash Tool guide with interactive progress tracking, prerequisite checklist, and complete troubleshooting.